STM32常见英文单词、术语、缩写等 |
您所在的位置:网站首页 › 定义域的英文简写 › STM32常见英文单词、术语、缩写等 |
其实大家学啥外设术语太多直接找对应外设的UMxxx(ST的User manual系列的PDF)就有归纳整理的,这些术语在ST很多手册的Acronyms and definitions部分都右有的, 例如: UM1725——Description of STM32F4 HAL and low-layer drivers 的Table 1 UM1734——STM32Cube™ USB device library 的Table 2 AAF——Alternate function 复用功能 (port multiplexing and remapping 端口复用和重映射) AHB 先进高性能总线 ALU——Arithmetic Logical Unit 算术逻辑单元(CPU负责几乎所有的计算任务的核心) API——Application Programming Interface 应用编程接口 ARG——argument 参数 ARR——auto-reload register 自动装载(寄存器) ARPE——auto-reload preload enable 自动预载(寄存器) asynchronous 异步的 BBIN——binary 二进制 brief 简介 BSP——board support package 板级支持包】 Byte 字节 8位长的数据或指令 CCalibration 校准 CC——Capture/Compare 捕获/比较 CDC——communication device class 通信设备类 CMSIS——Cortex MicroController Software Interface Standard Cortex 微控制器软件接口标准:独立于供应商的硬件抽象层,适用于基于 Arm Cortex 处理器的微控制器 CK_INT——clock internal 内部时钟 CNT——counter 计数器 Coefficient——系数 contants 常量 context 上下文环境 coupled 耦合的 critical——临界的 DD-Code 这是连接Cortex-M3核心的D-Code总线(常数和调试访问)与闪存数据存储器接口的总线 DEC——decimal 十进制 DFU——Device Firmware Upgrade 有USB接口的STM32型号从硬件或软件上支持 DISC——disconnect division 分频因子 domain n. 域,范围,定义域 downcounter n. 降值计数器 DMIPS——Dhrystone Million Instructions executed Per Second Dhrystone软件测算力的MIPS单位 duty cycle 占空比 Dhrystone 最常见的整数运算性能测试程序 Eelapsed 过去 EOC——end of convert 转换结束 ETR——External 外部 (信号) FFPEC——FLASH Program/Erase controller 闪存编程/擦除控制器 FS——Full Speed 全速(12 Mbps) function 1) 功能;2) 函数 Ggeneration 产生 HHAL——Hardware Abstraction Layer 硬件抽象层 Half Word 半字 16位长的数据或指令 handler n. 句柄 HEX——hexdadecimal 十六进制 HID——human interface device 人机界面设备 IIABR——Interrupt Active Bit Registers 中断激活标志位寄存器组 IAP——In-Application Programming 在程序中编程 I-Code:这是连接Cortex-M3核心的指令总线与闪存程序存储器接口的总线,指令预取是 在这个总线上实现的 ICP——In-Circuit Programming 在线编程 ICPR——Interrupt Clear-Pending Registers 中断解挂控制寄存器组 ISPR——Interrupt Set-Pending Registers 中断挂起控制寄存器组 ICER——Interrupt Clear-Enable Registers 中断除能寄存器组 idle 空闲的 LL库——low-layer drivers instance 寄存器指针 integrity 完整(测试完整性) Initialise 初始化 IRQ——Interrupt Request 中断请求 IRQn——Interrupt Request number 中断请求号 ISER——Interrupt Set-Enable Registers 中断使能寄存器组 iterator 迭代器 ITM——仪表跟踪单元 IPR——Interrupt Priority Registers 中断优先级控制的寄存器组 IWDG——independent watchdog 独立看门狗 Instance n. 实例; 例子; 事例; v.举例 JJTAG-DP JTAG 调试接口 提供基于JTAG(Joint Test Action Group 联合测试行动小组)协议的5线标准接口 K Llatch 锁存 LIR——latch interrupt request 锁存中断请求 LSB——Last(Least) Significant Bit,最低有效位 MMIPS——Million Instructions executed Per Second,每秒执行百万条指令,用来计算同一秒内系统的处理能力,即每秒执行了多少百万条指令 MFLOPS——Million Floating-point Operations per Second,主要用于测浮点计算能力。 MPU——1)Microprocessor Unit 微处理器;2)Micro Processor Unit 内存保护单元 MSB——Most Significant Bit, 最高有效位 MSC——mass storage device class 大容量存储类 MSP——1)MCU Specific Package MCU 特征包、MCU 实例化包;——2)MCU Support package MCU支持包 MUX——multiplexer (multiplexor)多路复用器,也称数据选择器(data selector) NNVIC——Nested Vectored Interrupt Controller 嵌套向量中断控制器 OOBL:选择字节加载单元 occure 发生 ODR——Output data rate 数据输出频率,出处:LIS3DH手册 CTRL_REG1 (20h)的ODR[3:0],单位Hz OTG——On-The-Go:OTG外设可运行时切换 HOST/DEVICE角色 overload 重载 PParity 奇偶检验(参数有 None、Odd、Even) parameter(s) n. 参数 period 1.(定时器的)自动装载值ARR(自动重装载寄存器(TIMx_ARR)) 2.周期,(物理学符号是 T) peripheral n. 外设 外围设备) PID——USB 产品标识:A USB device that is plugged in identifies itself by its VID/PID combination. A VID is a 16-bit vendor number (Vendor ID). A PID is a 16-bit product number (Product ID). The PC uses the VID/PID combination to find the drivers (if any) that are to be used for the USB device. platform 平台 polarity 极性 POR——Power-on reset PRI——priority 优先级 preemption priority 抢占优先级 prototype 原型 (functions prototypes 函数原型) PSC——prescaler n. 预分频器 Qqueue 队列 RRCC——Reset and clock control 时钟配置 repetition 重复(overload是 重载,不要混了) RES——resolution 分辨率 ret——retval——return value 返回值 restrict 限制 resume 恢复 Ssample——样本 SAK——slave acknowledge 从机应答 scheduler 调度器 SCSI——small computer system inerface 小型计算机系统接口 SMBus——STM32 I2C Slave 模式(从机模式) SWD——Serial Wire Debug 串行线调试 SWO——Serial Wire Output 串行线输出 SWV——Serial Wire Viewer 串行线查看器 SOF——Start of Frame 帧起始:Every millisecond (12000 full-bandwidth bit times), the USB host transmits a special SOF (start of frame) token, containing an 11-bit incrementing frame number in place of a device address. This is used to synchronize isochronous and interrupt data transfers. state . 状态 status n. 状态 stream 流(数据流、流的缓冲区) SUB——sub-address 子地址 suspend 挂起 SWD-DP SWD调试接口 提供基于SWD(Serial Wire Debug 串行线调试)协议的2 线标准接口 synchronous 同步的 Ttask 任务 TCB——task control block 任务控制块 THS——threshold 阈值 Trigger 触发 UUEV——update event 更新事件 UDIS——update disable 禁止产生更新事件 (UEV) USB——Universal Serial Bus 通用串行总线 VVCP——visual com port 虚拟串口 VID——USB 厂商标识:A USB device that is plugged in identifies itself by its VID/PID combination. A VID is a 16-bit vendor number (Vendor ID). A PID is a 16-bit product number (Product ID). The PC uses the VID/PID combination to find the drivers (if any) that are to be used for the USB device. WWhetstone 最常见的浮点运算性能测试程序 Word 字 32位长的数据或指令 WWDG——window watchdog 窗口看门狗 X Y Z |
今日新闻 |
推荐新闻 |
CopyRight 2018-2019 办公设备维修网 版权所有 豫ICP备15022753号-3 |