锐捷路由器端口映射设置 |
您所在的位置:网站首页 › 锐捷路由器查看命令在哪 › 锐捷路由器端口映射设置 |
网吧里有服务器采用私网的IP地址,提供WWW、FTP、E-mail等服务,现在想让公网上的电脑也能够访问这台服务器,配置如下: 由于路由器的WAN口采用的是公网的IP地址,如果需要局域网的服务器要提供给公网的电脑访问的话,那么采用端口映射的方式,可以实现。由于每种服务的端口都是不一样的(WWW服务:80端口;FTP服务:21端口),因此将服务器的各种端口与映射到公网的地址相应的端口上,这样公网上的电脑访问路由器的WAN口的地址,即可访问到局域网的服务器,下面一个例子进行说明: ![]() 为了实现这些功能,需要配置NAT静态映射功能。快速配置功能中不包含该功能的设置,因此需要在第一次启动路由器后使用“no”放弃快速配置然后进入特权用户模式进行高级设置: !进入特权用户层 Red-Giant>enable !进入全局配置层 Red-Giant#config terminal Enter configuration commands, one per line. End with CNTL/Z. !进入WAN口配置层 Red-Giant(config)#interface fastethernet 0 !配置WAN口地址 Red-Giant(config-if)#ip address 218.5.19.2 255.255.255.0 !设置WAN口为共享连接的Internet接入口 Red-Giant(config-if)#ip nat outside !启用WAN口 Red-Giant(config-if)#no shut !返回普通用户层 Red-Giant(config-if)#end Red-Giant# !这些是系统提示信息,系统提示WAN口链路处于UP状态(可通讯状态). %UPDOWN: Line protocol on Interface FastEthernet0, changed state to up %UPDOWN: Interface FastEthernet0, changed state to up Red-Giant#config terminal Enter configuration commands, one per line. End with CNTL/Z. !进入LAN口配置层 Red-Giant(config)#interface fastethernet 1 !配置LAN口地址 Red-Giant(config-if)#ip address 192.168.0.1 255.255.255.0 !设置LAN口为共享连接的Intranet接入口 Red-Giant(config-if)#ip nat inside !启用LAN口 Red-Giant(config-if)#no shut Red-Giant(config-if)#end Red-Giant# %UPDOWN: Line protocol on Interface FastEthernet1, changed state to up %UPDOWN: Interface FastEthernet1, changed state to up Red-Giant#config terminal Enter configuration commands, one per line. End with CNTL/Z. !配置默认路由以访问Internet Red-Giant(config)#ip route 0.0.0.0 0.0.0.0 fastethernet 0 218.5.19.1 !配置NAT快转优化 Red-Giant(config)#ip nat optimize !配置NAT应用的访问列表 Red-Giant(config)#access-list 1 permit any !配置连接共享规则 Red-Giant(config)#ip nat inside source list 1 interface fastethernet 0 !配置FTP服务器的静态映射 Red-Giant(config)#ip nat inside source static tcp 192.168.0.2 20 218.5.19.2 20 Red-Giant(config)#ip nat inside source static tcp 192.168.0.2 21 218.5.19.2 21 !配置WEB服务器的静态映射 Red-Giant(config)#ip nat inside source static tcp 192.168.0.3 80 218.5.19.2 80 !配置EMAIL服务器的静态映射 Red-Giant(config)#ip nat inside source static tcp 192.168.0.4 25 218.5.19.2 25 Red-Giant(config)#ip nat inside source static tcp 192.168.0.4 110 218.5.19.2 110 Red-Giant(config)#end Red-Giant# Red-Giant#config terminal Enter configuration commands, one per line. End with CNTL/Z. !配置远程用户Telnet访问口令 Red-Giant(config)#line vty 0 4 Red-Giant(config-line)#password remoteuser Red-Giant(config-line)#end Red-Giant# Red-Giant#config terminal Enter configuration commands, one per line. End with CNTL/Z. Red-Giant(config)#enable secret private !配置路由器名称 Red-Giant(config)#host NBR NBR(config)#end NBR# !保存配置 NBR#write Building configuration... [OK] NBR# 通过以上配置,公网上的电脑即可通过访问WAN口IP地址来达到访问局域网服务器的目的 上一篇:路由器的作用和工作原理-路由器如何工作 下一篇:如何提升路由器信号强度(手机路由器如何增加信号) |
今日新闻 |
推荐新闻 |
CopyRight 2018-2019 办公设备维修网 版权所有 豫ICP备15022753号-3 |