基于stm32蓝牙接收信息并显示在OLED上 |
您所在的位置：网站首页 › 显示屏幕上的微笑 › 基于stm32蓝牙接收信息并显示在OLED上 |
|
两个单片机基于蓝牙连接通信，可以使能串口，把蓝牙当作串口来使用。例如，蓝牙通过串口发送信息，蓝牙通过串口接收信息，这样就可以使两个单片机进行通信。下面代码是基于STM32蓝牙接收另外一块单片机蓝牙发送过来的温湿度信息，并显示在OLED上。 主函数 #include "stm32f10x.h" #include "OLED.h" #include "usart.h" extern u16 USART_RX_Flag; // 接收数据标志位 extern u8 USART_RX_Tmr; // 接收延时 u8 USART_RX_Com; // 接收完成标志位 u8 RXTemp=0; // 接收到的温度值 u8 RXHumi=0; // 接收到的湿度值 // 串口蓝牙接收的温湿度数据 void Display_Rxdata(u8 value1,u8 value2) { OLED_ShowString(1,1,"RT="); OLED_ShowString(1,7,"C"); OLED_ShowNum(1,5,value1,2); // 显示温度数据 OLED_ShowString(2,1,"RH="); OLED_ShowNum(2,5,value2,2); // 显示湿度数据 OLED_ShowString(2,7,"%"); } 接收程序 void Usart_receive(void) { if(USART_RX_Flag==1) { if(++USART_RX_Tmr>=1) // 接收延时 { USART_RX_Tmr =0; // 清零接收延时 USART_RX_Flag=0; // 清零标志位 USART_RX_STA =0; // 清零接收个数 USART_RX_Com =1; // 接收完成标志位置1 RXTemp= (USART_RX_BUF[0]-0x30)*10+USART_RX_BUF[1]-0x30; // ASCLL码转换 RXHumi= (USART_RX_BUF[2]-0x30)*10+USART_RX_BUF[3]-0x30; // ASCLL码转换 } } } int main（） { Usart2_Init(115200); NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); //中断优先级分组 分2组 OLED_Init(); while(1) { Usart_receive(); // 串口接收数据 Display_Rxdata(RXTemp,RXHumi); //OLED显示接收的温湿度 } }串口设置 串口设置 //硬件驱动 #include "usart.h" //C库 #include #include #include u16 USART_RX_STA=0; //接收状态标记 u16 USART_RX_Flag=0; //接收数据标志位 u8 USART_RX_Tmr=0; // 接收延时 u8 USART_RX_data; char USART_RX_BUF[USART_REC_LEN]; //接收缓冲,最大USART_REC_LEN个字节. void Usart2_Init(unsigned int baud) { GPIO_InitTypeDef gpio_initstruct; USART_InitTypeDef usart_initstruct; NVIC_InitTypeDef nvic_initstruct; RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE); RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2, ENABLE); //PA2 TXD gpio_initstruct.GPIO_Mode = GPIO_Mode_AF_PP; gpio_initstruct.GPIO_Pin = GPIO_Pin_2; gpio_initstruct.GPIO_Speed = GPIO_Speed_50MHz; GPIO_Init(GPIOA, &gpio_initstruct); //PA3 RXD gpio_initstruct.GPIO_Mode = GPIO_Mode_IN_FLOATING; gpio_initstruct.GPIO_Pin = GPIO_Pin_3; gpio_initstruct.GPIO_Speed = GPIO_Speed_50MHz; GPIO_Init(GPIOA, &gpio_initstruct); usart_initstruct.USART_BaudRate = baud; usart_initstruct.USART_HardwareFlowControl = USART_HardwareFlowControl_None; //无硬件流控 usart_initstruct.USART_Mode = USART_Mode_Rx | USART_Mode_Tx; //接收和发送 usart_initstruct.USART_Parity = USART_Parity_No; //无校验 usart_initstruct.USART_StopBits = USART_StopBits_1; //1位停止位 usart_initstruct.USART_WordLength = USART_WordLength_8b; //8位数据位 USART_Init(USART2, &usart_initstruct); USART_Cmd(USART2, ENABLE); //使能串口 USART_ITConfig(USART2, USART_IT_RXNE, ENABLE); //使能接收中断 nvic_initstruct.NVIC_IRQChannel = USART2_IRQn; nvic_initstruct.NVIC_IRQChannelCmd = ENABLE; nvic_initstruct.NVIC_IRQChannelPreemptionPriority = 0; nvic_initstruct.NVIC_IRQChannelSubPriority = 0; NVIC_Init(&nvic_initstruct); USART_ClearFlag(USART2,USART_FLAG_TC);//清除USARTx的待处理标志位 }串口.h #ifndef _USART_H_ #define _USART_H_ #include "stm32f10x.h" #define USART_REC_LEN 400 //定义最大接收字节数 200 extern char USART_RX_BUF[USART_REC_LEN]; //接收缓冲,最大USART_REC_LEN个字节.末字节为换行符 extern u16 USART_RX_STA; //接收状态标记 void Usart2_Init(unsigned int baud); void USART2_IRQHandler(void); #endifOLED设置 #include "stm32f10x.h" #include "OLED_Font.h" #include "OLED.h" /*引脚配置*/ #define OLED_W_SCL(x) GPIO_WriteBit(GPIOB, GPIO_Pin_8, (BitAction)(x)) #define OLED_W_SDA(x) GPIO_WriteBit(GPIOB, GPIO_Pin_9, (BitAction)(x)) /*引脚初始化*/ void OLED_I2C_Init(void) { RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE); GPIO_InitTypeDef GPIO_InitStructure; GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_OD; GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8; GPIO_Init(GPIOB, &GPIO_InitStructure); GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9; GPIO_Init(GPIOB, &GPIO_InitStructure); OLED_W_SCL(1); OLED_W_SDA(1); } /** * @brief I2C开始 * @param 无 * @retval 无 */ void OLED_I2C_Start(void) { OLED_W_SDA(1); OLED_W_SCL(1); OLED_W_SDA(0); OLED_W_SCL(0); } /** * @brief I2C停止 * @param 无 * @retval 无 */ void OLED_I2C_Stop(void) { OLED_W_SDA(0); OLED_W_SCL(1); OLED_W_SDA(1); } /** * @brief I2C发送一个字节 * @param Byte 要发送的一个字节 * @retval 无 */ void OLED_I2C_SendByte(uint8_t Byte) { uint8_t i; for (i = 0; i < 8; i++) { OLED_W_SDA(Byte & (0x80 >> i)); OLED_W_SCL(1); OLED_W_SCL(0); } OLED_W_SCL(1); //额外的一个时钟，不处理应答信号 OLED_W_SCL(0); } /** * @brief OLED写命令 * @param Command 要写入的命令 * @retval 无 */ void OLED_WriteCommand(uint8_t Command) { OLED_I2C_Start(); OLED_I2C_SendByte(0x78); //从机地址 OLED_I2C_SendByte(0x00); //写命令 OLED_I2C_SendByte(Command); OLED_I2C_Stop(); } /** * @brief OLED写数据 * @param Data 要写入的数据 * @retval 无 */ void OLED_WriteData(uint8_t Data) { OLED_I2C_Start(); OLED_I2C_SendByte(0x78); //从机地址 OLED_I2C_SendByte(0x40); //写数据 OLED_I2C_SendByte(Data); OLED_I2C_Stop(); } /** * @brief OLED设置光标位置 * @param Y 以左上角为原点，向下方向的坐标，范围：0~7 * @param X 以左上角为原点，向右方向的坐标，范围：0~127 * @retval 无 */ void OLED_SetCursor(uint8_t Y, uint8_t X) { OLED_WriteCommand(0xB0 | Y); //设置Y位置 OLED_WriteCommand(0x10 | ((X & 0xF0) >> 4)); //设置X位置低4位 OLED_WriteCommand(0x00 | (X & 0x0F)); //设置X位置高4位 } /** * @brief OLED清屏 * @param 无 * @retval 无 */ void OLED_Clear(void) { uint8_t i, j; for (j = 0; j < 8; j++) { OLED_SetCursor(j, 0); for(i = 0; i < 128; i++) { OLED_WriteData(0x00); } } } /** * @brief OLED显示一个字符 * @param Line 行位置，范围：1~4 * @param Column 列位置，范围：1~16 * @param Char 要显示的一个字符，范围：ASCII可见字符 * @retval 无 */ void OLED_ShowChar(uint8_t Line, uint8_t Column, char Char) { uint8_t i; OLED_SetCursor((Line - 1) * 2, (Column - 1) * 8); //设置光标位置在上半部分 for (i = 0; i < 8; i++) { OLED_WriteData(OLED_F8x16[Char - ' '][i]); //显示上半部分内容 } OLED_SetCursor((Line - 1) * 2 + 1, (Column - 1) * 8); //设置光标位置在下半部分 for (i = 0; i < 8; i++) { OLED_WriteData(OLED_F8x16[Char - ' '][i + 8]); //显示下半部分内容 } } /** * @brief OLED显示字符串 * @param Line 起始行位置，范围：1~4 * @param Column 起始列位置，范围：1~16 * @param String 要显示的字符串，范围：ASCII可见字符 * @retval 无 */ void OLED_ShowString(uint8_t Line, uint8_t Column, char *String) { uint8_t i; for (i = 0; String[i] != '\0'; i++) { OLED_ShowChar(Line, Column + i, String[i]); } } /** * @brief OLED次方函数 * @retval 返回值等于X的Y次方 */ uint32_t OLED_Pow(uint32_t X, uint32_t Y) { uint32_t Result = 1; while (Y--) { Result *= X; } return Result; } /** * @brief OLED显示数字（十进制，正数） * @param Line 起始行位置，范围：1~4 * @param Column 起始列位置，范围：1~16 * @param Number 要显示的数字，范围：0~4294967295 * @param Length 要显示数字的长度，范围：1~10 * @retval 无 */ void OLED_ShowNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length) { uint8_t i; for (i = 0; i < Length; i++) { OLED_ShowChar(Line, Column + i, Number / OLED_Pow(10, Length - i - 1) % 10 + '0'); } } /** * @brief OLED显示数字（十进制，带符号数） * @param Line 起始行位置，范围：1~4 * @param Column 起始列位置，范围：1~16 * @param Number 要显示的数字，范围：-2147483648~2147483647 * @param Length 要显示数字的长度，范围：1~10 * @retval 无 */ void OLED_ShowSignedNum(uint8_t Line, uint8_t Column, int32_t Number, uint8_t Length) { uint8_t i; uint32_t Number1; if (Number >= 0) { OLED_ShowChar(Line, Column, '+'); Number1 = Number; } else { OLED_ShowChar(Line, Column, '-'); Number1 = -Number; } for (i = 0; i < Length; i++) { OLED_ShowChar(Line, Column + i + 1, Number1 / OLED_Pow(10, Length - i - 1) % 10 + '0'); } } /** * @brief OLED显示数字（十六进制，正数） * @param Line 起始行位置，范围：1~4 * @param Column 起始列位置，范围：1~16 * @param Number 要显示的数字，范围：0~0xFFFFFFFF * @param Length 要显示数字的长度，范围：1~8 * @retval 无 */ void OLED_ShowHexNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length) { uint8_t i, SingleNumber; for (i = 0; i < Length; i++) { SingleNumber = Number / OLED_Pow(16, Length - i - 1) % 16; if (SingleNumber < 10) { OLED_ShowChar(Line, Column + i, SingleNumber + '0'); } else { OLED_ShowChar(Line, Column + i, SingleNumber - 10 + 'A'); } } } /** * @brief OLED显示数字（二进制，正数） * @param Line 起始行位置，范围：1~4 * @param Column 起始列位置，范围：1~16 * @param Number 要显示的数字，范围：0~1111 1111 1111 1111 * @param Length 要显示数字的长度，范围：1~16 * @retval 无 */ void OLED_ShowBinNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length) { uint8_t i; for (i = 0; i < Length; i++) { OLED_ShowChar(Line, Column + i, Number / OLED_Pow(2, Length - i - 1) % 2 + '0'); } } void OLED_Init(void) { uint32_t i, j; for (i = 0; i < 1000; i++) //上电延时 { for (j = 0; j < 1000; j++); } OLED_I2C_Init(); //端口初始化 OLED_WriteCommand(0xAE); //关闭显示 OLED_WriteCommand(0xD5); //设置显示时钟分频比/振荡器频率 OLED_WriteCommand(0x80); OLED_WriteCommand(0xA8); //设置多路复用率 OLED_WriteCommand(0x3F); OLED_WriteCommand(0xD3); //设置显示偏移 OLED_WriteCommand(0x00); OLED_WriteCommand(0x40); //设置显示开始行 OLED_WriteCommand(0xA1); //设置左右方向，0xA1正常 0xA0左右反置 OLED_WriteCommand(0xC8); //设置上下方向，0xC8正常 0xC0上下反置 OLED_WriteCommand(0xDA); //设置COM引脚硬件配置 OLED_WriteCommand(0x12); OLED_WriteCommand(0x81); //设置对比度控制 OLED_WriteCommand(0xCF); OLED_WriteCommand(0xD9); //设置预充电周期 OLED_WriteCommand(0xF1); OLED_WriteCommand(0xDB); //设置VCOMH取消选择级别 OLED_WriteCommand(0x30); OLED_WriteCommand(0xA4); //设置整个显示打开/关闭 OLED_WriteCommand(0xA6); //设置正常/倒转显示 OLED_WriteCommand(0x8D); //设置充电泵 OLED_WriteCommand(0x14); OLED_WriteCommand(0xAF); //开启显示 OLED_Clear(); //OLED清屏 }OLED头文件 #ifndef __OLED_H #define __OLED_H //#define OLED_CMD 0 //写命令.0 //#define OLED_DATA 1 //写数据 void OLED_Init(void); void OLED_Clear(void); void OLED_ShowChar(uint8_t Line, uint8_t Column, char Char); void OLED_ShowString(uint8_t Line, uint8_t Column, char *String); void OLED_ShowNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length); void OLED_ShowSignedNum(uint8_t Line, uint8_t Column, int32_t Number, uint8_t Length); void OLED_ShowHexNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length); void OLED_ShowBinNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length); //void OLED_WR_Byte(unsigned char dat,unsigned char cmd); //void OLED_Set_Pos(unsigned char x, unsigned char y); #endifOLED字模库 #ifndef __OLED_FONT_H #define __OLED_FONT_H /*OLED字模库，宽8像素，高16像素*/ const uint8_t OLED_F8x16[][16]= { 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,// 0 0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00,//! 1 0x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//" 2 0x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00, 0x04,0x3F,0x04,0x04,0x3F,0x04,0x04,0x00,//# 3 0x00,0x70,0x88,0xFC,0x08,0x30,0x00,0x00, 0x00,0x18,0x20,0xFF,0x21,0x1E,0x00,0x00,//$ 4 0xF0,0x08,0xF0,0x00,0xE0,0x18,0x00,0x00, 0x00,0x21,0x1C,0x03,0x1E,0x21,0x1E,0x00,//% 5 0x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00, 0x1E,0x21,0x23,0x24,0x19,0x27,0x21,0x10,//& 6 0x10,0x16,0x0E,0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//' 7 0x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00, 0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00,//( 8 0x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00, 0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00,//) 9 0x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00, 0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00,//* 10 0x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00, 0x01,0x01,0x01,0x1F,0x01,0x01,0x01,0x00,//+ 11 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x80,0xB0,0x70,0x00,0x00,0x00,0x00,0x00,//, 12 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,//- 13 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,//. 14 0x00,0x00,0x00,0x00,0x80,0x60,0x18,0x04, 0x00,0x60,0x18,0x06,0x01,0x00,0x00,0x00,/// 15 0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00, 0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,//0 16 0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00, 0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//1 17 0x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00, 0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00,//2 18 0x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00, 0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00,//3 19 0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00, 0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00,//4 20 0x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00, 0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00,//5 21 0x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00, 0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00,//6 22 0x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00, 0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,//7 23 0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00, 0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00,//8 24 0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00, 0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00,//9 25 0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00, 0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,//: 26 0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00, 0x00,0x00,0x80,0x60,0x00,0x00,0x00,0x00,//; 27 0x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00, 0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00,//< 28 0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00, 0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00,//= 29 0x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00, 0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00,//> 30 0x00,0x70,0x48,0x08,0x08,0x08,0xF0,0x00, 0x00,0x00,0x00,0x30,0x36,0x01,0x00,0x00,//? 31 0xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00, 0x07,0x18,0x27,0x24,0x23,0x14,0x0B,0x00,//@ 32 0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00, 0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20,//A 33 0x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00, 0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00,//B 34 0xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00, 0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00,//C 35 0x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00, 0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00,//D 36 0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00, 0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00,//E 37 0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00, 0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00,//F 38 0xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00, 0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00,//G 39 0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08, 0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20,//H 40 0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00, 0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//I 41 0x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00, 0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00,//J 42 0x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00, 0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00,//K 43 0x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00, 0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00,//L 44 0x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00, 0x20,0x3F,0x00,0x3F,0x00,0x3F,0x20,0x00,//M 45 0x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08, 0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00,//N 46 0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00, 0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00,//O 47 0x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00, 0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00,//P 48 0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00, 0x0F,0x18,0x24,0x24,0x38,0x50,0x4F,0x00,//Q 49 0x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00, 0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20,//R 50 0x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00, 0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00,//S 51 0x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00, 0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//T 52 0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08, 0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//U 53 0x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08, 0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00,//V 54 0xF8,0x08,0x00,0xF8,0x00,0x08,0xF8,0x00, 0x03,0x3C,0x07,0x00,0x07,0x3C,0x03,0x00,//W 55 0x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08, 0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20,//X 56 0x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00, 0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//Y 57 0x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00, 0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00,//Z 58 0x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00, 0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00,//[ 59 0x00,0x0C,0x30,0xC0,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00,//\ 60 0x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00, 0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00,//] 61 0x00,0x00,0x04,0x02,0x02,0x02,0x04,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//^ 62 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,//_ 63 0x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//` 64 0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00, 0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20,//a 65 0x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00, 0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00,//b 66 0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00, 0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00,//c 67 0x00,0x00,0x00,0x80,0x80,0x88,0xF8,0x00, 0x00,0x0E,0x11,0x20,0x20,0x10,0x3F,0x20,//d 68 0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00, 0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00,//e 69 0x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18, 0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//f 70 0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00, 0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00,//g 71 0x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00, 0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//h 72 0x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00, 0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//i 73 0x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00, 0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,//j 74 0x08,0xF8,0x00,0x00,0x80,0x80,0x80,0x00, 0x20,0x3F,0x24,0x02,0x2D,0x30,0x20,0x00,//k 75 0x00,0x08,0x08,0xF8,0x00,0x00,0x00,0x00, 0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//l 76 0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00, 0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F,//m 77 0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00, 0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//n 78 0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00, 0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//o 79 0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00, 0x80,0xFF,0xA1,0x20,0x20,0x11,0x0E,0x00,//p 80 0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00, 0x00,0x0E,0x11,0x20,0x20,0xA0,0xFF,0x80,//q 81 0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00, 0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00,//r 82 0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00, 0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00,//s 83 0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00, 0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00,//t 84 0x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00, 0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20,//u 85 0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80, 0x00,0x01,0x0E,0x30,0x08,0x06,0x01,0x00,//v 86 0x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80, 0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00,//w 87 0x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00, 0x00,0x20,0x31,0x2E,0x0E,0x31,0x20,0x00,//x 88 0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80, 0x80,0x81,0x8E,0x70,0x18,0x06,0x01,0x00,//y 89 0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00, 0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00,//z 90 0x00,0x00,0x00,0x00,0x80,0x7C,0x02,0x02, 0x00,0x00,0x00,0x00,0x00,0x3F,0x40,0x40,//{ 91 0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00, 0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,//| 92 0x00,0x02,0x02,0x7C,0x80,0x00,0x00,0x00, 0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x00,//} 93 0x00,0x06,0x01,0x01,0x02,0x02,0x04,0x04, 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//~ 94 }; #endif |
今日新闻 |
推荐新闻 |
| CopyRight 2018-2019 办公设备维修网 版权所有 豫ICP备15022753号-3 |