思科CISCO常用命令汇总 |
您所在的位置:网站首页 › 思科路由器查看历史命令 › 思科CISCO常用命令汇总 |
视图模式介绍
1.普通视图router> 2.特权视图router# / 在普通模式下输入enable 3.全局视图router(config)#/ 在特权模式下输入configt 4.接口视图router(config-if)#/在全局模式下输入int 接口名称例如int s0 或 int e0 5.路由协议视图router ( config-route ) #/ 在全局模式下输入router 动态路由协议名称
1基本配置:
1. router>enable / 进入特权模式 2. router#conft / 进入全局配置模式 3. router(config)#hostname xxx /设置设备名称就好像给我们的计算机起个名字 4. router(config)#enable password xxx /设置特权口令 5. router(config)#no ip domain lookup /不允许路由器缺省使用DNS解析命令 6. router(config)#Service password-encryption /对所有在路由器上输入的口令进行暗文加密 7. router(config)#line vty 0 4 /进入设置telnet服务模式 router(config-line)#password xxx /设置 telnet 的密码 router(config-line)#login /使能可以登陆 8. router(config)#line con 0 /进入控制口的服务模式 router(config-line)#password xxx /要设置 console 的密码 router(config-line)#login /使能可以登陆
2接口配置
1. router(config)# int s0 / 进入接口配置模式serial 0 端口配置 (如果是模块化的路由器前面加上槽 位编号,例如serial0/0 代表这个路由器的0 槽位上的第一个接口) 2.router(config-if)#ip add xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx / 添加 ip 地址和掩码 3.router(config-if)#enca hdlc /ppp捆绑链路协议hdlc 或者 ppp 思科缺省串口封装的链路层协议 是 HDLC 所以在 show run 配置的时候接口上的配置没有,如果要封装为别的链路层协议例如PPP/FR/X25就是看到接口下的enca ppp 或者 enca fr 4.router(config)#int loopback /建立环回口(逻辑接口 )模拟不同的本机网段 router(config-if)#ip add xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx / 添加ip 地址和掩码给环回口在物理接口 上配置了ip 地址后用no shut 启用这个物理接口反之可以用shutdown 管理性的关闭接口
3路由配置
1.静态路由 router(config)#ip route xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx 下一跳或自己的接口 2.缺省路由 router(config)#ip route 0.0.0.0 0.0.0.0 s0添加缺省路由 3.动态路由rip 协议 router(config)#router rip /启动 rip 协议 router(config-router)#network xxx.xxx.xxx.xxx /宣告自己的网段router(config-router)#version 2 /转 换为 rip2 版本 router(config-router)#noauto-summary /关闭自动汇总功能,ripV2才有作用 router(config-router)#passive-in 接 口 名 / 启 动 本 路 由 器 的 那 个 接 口 为 被 动 接 口 router(config-router)#neixxx.xxx.xxx.xxx/广播转单播报文,指定邻居的接 ip 4.动态路由eigrp 协议 router(config)#router eigrp xxx /启动 eigrp 协议 router(config-router)#network xxx.xxx.xxx.xxx /宣告自己的网段 router(config-router)#variance xxx /调整倍数因子,使用不等价的负载均衡eigrp 协议 router(config-router)#noauto-summary /关闭自动汇总功能ospf 协议 5.动态路由ospf协议 router(config)router ospf xxx /启动协议 router(config-router)network xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx(反掩码)area xxx / 宣告自己的接口 或网段在ospf 的区域中可以把不同接口宣告在不同区域中
4保存当前修改/运行的配置:
1.router#write /将 RAM 中的当前配置存储到NVRAM 中,下次路由器启动就是执行保存的配置 2.router#Copy running-config startup-config /命令与write 效果一样
5一般常用命令
1.exit命令 router(config-if)#exit router(config)# router (config-router)#exit router(config)# router(config-line)#exit router(config)# router (config)#exit router# exit 命令 / 从接口、协议、line 等视图模式下退回到全局配置模式,或从全局配置模式退回到特权模式 2.end命令 router(config-if)#end router(config-router)#end router(config-line)#end router# end 命令 / 从任何视图直接回到特权模式 3.logout router#Logout / 退出当前路由器登陆模式相对与windows 的注销 4.reload命令 router#reload / 重新启动路由器 (热启动)冷启动就是关闭路由器再打开电源开关 5.show 命令 特权模式下:router#show ip route /查看当前的路由表router#cleariproute*/清楚当前的路由表 router#show ip protocol /查看当前路由器运行的动态路由协议情况 router#show ip int brief /查看 当前的路由器的接口ip地址启用情况 router#show running-config /查看当前运行配置 router#show startup-config /查看启动配置 router#debug ip pack / 打开 ip 报文的调试 router#terminal monitor / 输出到终端上显示调试信息 router#show ip eigrp neighbors /查看 eigrp 协议的邻居表 router#show ip eigrp topology /查看 eigrp 协议 的拓朴表 router#show ip eigrp interface /查 看当然路由器运行eigrp协议的 接口情况 router#show ip ospf neighbor /查看当前路由器的ospf 协议的邻居表 router#show ip ospf interface /查看当然路由器运行ospf协议的接口情况 router#clear ip ospf process / 清楚当然路由器ospf 协议的进程 router#Show interfaces / 显示设置在路由器和访问服务器上所有接口的统计信息. 显示路由器 上配置的所有接口的状态 router#Show interfaces serial / 显示关于一个串口的信息 router#Show ip interface /列出一个接口的IP 信息和状态的小结,列出接口的状态和全局参数
|
今日新闻 |
推荐新闻 |
CopyRight 2018-2019 办公设备维修网 版权所有 豫ICP备15022753号-3 |