华为12800系列交换机堆叠配置 |
您所在的位置:网站首页 › 华为交换机的堆叠配置 › 华为12800系列交换机堆叠配置 |
个别词汇说明: 1、commit命令:是华为CE设备的配置命令完成后,使用commit使得配置命令生效。 #查看未commit生效配置的命令: display configuration candidate #清空未commit配置可以用这个命令: clear configuration candidate 2、堆叠端口:这里的堆叠端口指的是逻辑的两台设备连接的端口,需要将物理的端口加入到堆叠端口中。
1、配置思路 1、连接堆叠线缆,最好使用华为原厂的堆叠线,比较有安全保证。 2、SwitchA和SwitchB上分别配置相同的堆叠域和堆叠的连接方式。分别配置不同的堆叠成员编号和堆叠成员优先级。 3、在SwitchA和SwitchB上分别创建堆叠端口,并将要堆叠的物理端口加入到堆叠端口中。 4、在SwitchA和SwitchB保存配置,使用堆叠功能。 2、配置命令1、连接堆叠线缆: 连接SwitchA和SwitchB间的堆叠线缆。如果选择的堆叠连接方式为主控板直连方式,则需要连接主控板上的SIP口和业务板上的堆叠物理成员端口;如果为业务板直连方式,则无需连接SIP口。 2、 配置SwitchA、SwitchB的堆叠属性: # 配置SwitchA的堆叠成员ID为1,优先级为150,Domain ID为10,堆叠连接方式为业务板连接方式。 system-view [~HUAWEI] sysname SwitchA [*HUAWEI] commit *CE设备配置生效的命令 [~SwitchA] stack [~SwitchA-stack] stack member 1 *堆叠成员为1 [~SwitchA-stack] stack priority 150 *堆叠成员优先级,越大越优先,成为master [*SwitchA-stack] stack domain 10 *堆叠域为10,域必须一样 [*SwitchA-stack] stack link-type linecard-direct *堆叠连接方式,使用业务板堆叠 [*SwitchA-stack] quit [*SwitchA]commit *上述配置命令生效 # 配置SwitchB的堆叠成员ID为2,优先级为100,Domain ID为10,堆叠连接方式为主控板直连方式。 system-view [~HUAWEI] sysname SwitchB [*HUAWEI] commit [~SwitchB] stack [~SwitchB-stack] stack member 2 Warning: The device will use the configuration of member ID 2 after the device resets. Continue? [Y/N]: y [*SwitchB-stack] stack priority 100 [*SwitchB-stack] stack domain 10 [*SwitchB-stack] stack link-type linecard-direct [*SwitchB-stack] quit [*SwitchB] commit 3、配置堆叠端口 # 在SwitchA上创建堆叠端口,并将端口10GE3/0/0~10GE3/0/3加入堆叠端口。 # 在SwitchB上创建堆叠端口,并将端口10GE3/0/0~10GE3/0/3加入堆叠端口。 SwitchB的配置与SwitchA类似,配置过程略。 [~SwitchA] port-group group1 *创建物理端口组1 [*SwitchA-port-group-group1] group-member 10GE 3/0/0 to 10GE 3/0/3 *添加要堆叠的4个物理端口 [*SwitchA-port-group-group1] shutdown *加入堆叠端口之前先关闭物理端口 [*SwitchA-port-group-group1] quit [*SwitchA] commit [~SwitchA] interface stack-port 1 *进入堆叠端口 [*SwitchA-Stack-Port1] port member-group interface 10GE 3/0/0 to 10GE 3/0/3 [*SwitchA-Stack-Port1] quit [*SwitchA] commit [~SwitchA] port-group group1 [~SwitchA-port-group-group1] undo shutdown *加入堆叠端口后,开启物理端口 [*SwitchA-port-group-group1] quit [*SwitchA] commit [~SwitchA] quit 4、检查堆叠配置信息# 上述配置完成后,建议用户执行命令display stack configuration查看以上配置信息是否与预期的一致。以查看SwitchA为例。 display stack configuration Oper : Operation Conf : Configuration * : Offline configuration Isolated Port: The port is in stack mode, but does not belong to any Stack-Port
Attribute Configuration: --------------------------------------------------------------- MemberID Domain Priority Mode Enable Oper(Conf) Oper(Conf) Oper(Conf) Oper(Conf) Oper --------------------------------------------------------------- 1(1) --(10) 100(150) MB(LC) Disable *括号中重启生效 ---------------------------------------------------------------
Stack-Port Configuration: -------------------------------------------------------------------------------- Stack-Port Member Ports -------------------------------------------------------------------------------- Stack-Port1 10GE3/0/0 10GE3/0/1 10GE3/0/2 10GE3/0/3 -------------------------------------------------------------------------------- 5、保存配置并使能设备堆叠功能 # 保存SwitchA的配置并使能堆叠功能。 save Warning: The current configuration will be written to the device. Continue? [Y/N]: y system-view [~SwitchA] stack [~SwitchA-stack] stack enable Warning: Make sure that one or more dual-active detection methods are configured once the conversion is complete and the device ente rs the stack mode. Current configuration will be converted to the next startup saved-configuration file of stack mode. System will reboot. Continue? [Y/N]: y # 保存SwitchB的配置并使能堆叠功能。 save Warning: The current configuration will be written to the device. Continue? [Y/N]: y system-view [~SwitchB] stack [~SwitchB-stack] stack enable Warning: Make sure that one or more dual-active detection methods are configured once the conversion is complete and the device ente rs the stack mode. Current configuration will be converted to the next startup saved-configuration file of stack mode. System will reboot. Continue? [Y/N]: y 6、验证 # 通过Console口或管理网口登录堆叠系统,使用命令查看堆叠是否组建成功。当通过管理网口登录时,需要使用主交换机的IP地址。 display stack -------------------------------------------------------------------------------- MemberID Role MAC Priority DeviceType Description -------------------------------------------------------------------------------- 1 Master 006d-8835-2b00 150 CE12804 2 Standby 006d-8835-2c00 100 CE12804 -------------------------------------------------------------------------------- 说明: 在检查堆叠已成功建立后,建议用户立即使用save命令保存堆叠系统配置。 save Warning: The current configuration will be written to the device. Continue? [Y/N]: y |
今日新闻 |
推荐新闻 |
CopyRight 2018-2019 办公设备维修网 版权所有 豫ICP备15022753号-3 |