Brief: This quick trick shows you how to find devices connected to your local network in Linux.

Wireless networks have always been a desirable target for wannabe hackers. Wireless networks are also more vulnerable to hacking than the wired ones.

Forget hacking, do you ever wonder that someone might be leeching off your hard paid wifi network? Maybe a neighbor who once connected to your network and now uses it as his/her own?

It would be nice to check what devices are on your network. This way you can also see if there are some unwanted devices on your network.

So you might end up thinking, “how do I find what devices are connected to my network”?

I’ll show you how to do that in this quick tutorial. Not only it’s a good idea from security point of view, it is also a good little exercise if you have interest in networking.

We will use both, command line and GUI, way for finding out what devices are connected to your local network in Linux. The process is very simple and easy to use even for beginners.

Before you see any of that, let me tell you that your router should also be able to show all the connected devices. Check your gateway ip address and then type it in a browser. This is usually the browser interface for your router. Enter the username and password and you can see all the details and devices connected to the router.

If you don’t remember the router password or you don’t want to go that way, here’s what else you could do.

nmap is one of the most popular network scanning tool in Linux. Use the following command to install nmap in Ubuntu based Linux distributions:

You can easily install it in other Linux distributions as well. It should be in the official software repository.

Now we need to know the IP address range of the network. Use the ifconfig command to find the IP address in Linux. Look for wlan0 if you are using wifi or eth0 if you are using Ethernet.

[email protected]:~$ ifconfigwlan0 Link encap:Ethernet HWaddr 70:f1:a1:c2:f2:e9inet addr:192.168.1.91 Bcast:192.168.1.255 Mask:255.255.255.0inet6 addr: fe80::73f1:a1ef:fec2:f2e8/64 Scope:LinkUP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1RX packets:2135051 errors:0 dropped:0 overruns:0 frame:0TX packets:2013773 errors:0 dropped:0 overruns:0 carrier:0collisions:0 txqueuelen:1000RX bytes:1434994913 (1.4 GB) TX bytes:636207445 (636.2 MB)

The important things are highlighted in bold. As you see my IP is 192.168.1.91 and the subnet mask is 255.255.255.0 which means that the ip address range on my network varies from 192.168.1.0 to 192.168.1.255.

You may also use ip a command to know your IP address in Ubuntu and other Linux distributions.

At the same time, I’ll recommend you to read about basic Linux networking commands for more information.

It is advisable to use root privileges while scanning the network for more accurate information. Use the nmap command in the following way:

[email protected]:~$ sudo nmap -sn 192.168.1.0/24Starting Nmap 5.21 ( http://nmap.org ) at 2012-09-01 21:59 CEST

Nmap scan report for neufbox (192.168.1.1)Host is up (0.012s latency).MAC Address: E0:A1:D5:72:5A:5C (Unknown)Nmap scan report for takshak-bambi (192.168.1.91)Host is up.Nmap scan report for android-95b23f67te05e1c8 (192.168.1.93)Host is up (0.36s latency).

As you can see that there are three devices connected to my network. The router itself, my laptop and my Galaxy S2.

If you are wondering about why I used 24 in the above command, you should know a little about CIDR notation. It basically means that the scanning will be from 192.168.1.0 to 192.168.1.255.

When I first wrote this article, there was no GUI tool for this task. Then I came across a new network monitoring tool being developed for elementary OS. I suggested including a periodic device scan feature in this tool and the developer readily agreed.

So, now we have a GUI tool that does this task. It’s called Nutty (last updated in 2019). Just install this app and run it. It will periodically scan for new devices on the network and will notify you if there is a new device.

This application is only available for elementary OS, Ubuntu and hopefully, other Ubuntu based Linux distributions. You can find installation instructions on this detailed article on Nutty.

Oh, you can also log in to your router and see the devices connected to your devices. I let you figure the best way to find devices connected to your network.