ubuntu配置静态路由及重启生效 |
您所在的位置:网站首页 › ubuntu增加路由表 › ubuntu配置静态路由及重启生效 |
ubuntu配置静态路由及重启生效 第一种方法:使用route命令(添加临时路由) 添加到主机的路由# route add -host 192.168.1.123 dev eth0 # route add -host 192.168.1.123 gw 192.168.1.1 添加到网络的路由# route add -net 192.168.1.123 netmask 255.255.255.0 eth0 # route add -net 192.168.1.123 netmask 255.255.255.0 gw 192.168.1.1 # route add -net 192.168.1.123 netmask 255.255.255.0 gw 192.168.1.1 eth1 # route add -net 192.168.1.0/24 eth1 添加默认网关# route add default gw 192.168.1.1 删除路由# route del -host 192.168.1.11 dev eth0 # route del -net 192.168.1.123 netmask 255.255.255.0 第二种方法: 修改/etc/rc.local修改/etc/rc.local,只是要注意的一点是不要卸载 "exit 0"的后面 vi /etc/rc.local route add default gw 192.168.1.1 这样在系统启动的时候会自动加入相关的路由设置 注: (1)如果某个系统服务,比如说是NFS服务,这个服务是在启动network服务之后,在执行rc.local之前,如果你设置的有自动挂载的nfs,那么,这里链路的不通畅,会造成挂载的失败。 (2)如果你重启了网络服务器,那么路由就失效了,这个时候你不得不重新加载这个文件,但是如果你是远程操作的呢?所以,这个方法不是非常的不推荐 第三种方法:修改interfaces文件up route add -net 192.168.1.0 netmask 255.255.255.0 gw 192.168.1.1 可以看到这个格式和route命令的唯一区别在于,在前面多了一个up 下面列出我的interface文件仅供参考,由于安全因素,这里的ip我都用xx替代了: # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx gateway xxx.xxx.xxx.xxx auto eth0:0 iface eth0:0 inet static address xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx #dns-nameservers 202.102.224.68 202.102.227.68 up route add -net xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx gw xxx.xxx.xxx.xxx eth0 up route add -net xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx gw xxx.xxx.xxx.xxx eth0 up route add -net xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx gw xxx.xxx.xxx.xxx eth0 第四种:在/etc/sysconfig/networknetwork里添加到文件末尾,格式如下 vi /etc/sysconfig/network GATEWAY=gw-ip 或者 GATEWAY=gw-dev 注:这种方式从外观上来看只能用于添加默认网关了,对于多路网络环境貌似不太适合的样子 第五种:直接写入ifcfg文件在配置ip地址的时候直接将GATEWAY的配置写入ifcfg文件,形式:GATEWAY=gw-ip 适合添加默认路由 第六种:写入/etc/sysconfig/static-routes文件默认在/etc/sysconifg目录中是没有这个文件的,需要我们手工创建,对这个文件的调用在下面: /etc/init.d/network: 159 # Add non interface-specific static-routes. 160 if [ -f /etc/sysconfig/static-routes ]; then 161 grep "^any" /etc/sysconfig/static-routes | while read ignore args ; do 162 /sbin/route add -$args 163 done |
CopyRight 2018-2019 办公设备维修网 版权所有 豫ICP备15022753号-3 |