《（高清正版） ISO8501-1-2007》由会员分享，可在线阅读，更多相关《（高清正版） ISO8501-1-2007（96页珍藏版）》请在凡人图书馆上搜索。

1、 Reference numberNumro de rfrenceISO 8501-1:2007(E/F) ISO and SIS 2007/ISO et SIS 2007 INTERNATIONAL STANDARD NORME INTERNATIONALEISO8501-1Second editionDeuxime dition2007-05-01Preparation of steel substrates before application of paints and related products Visual assessment of surface cleanliness

2、Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings Prparation des subjectiles dacier avant application de peintures et de produits assimils valuation visuelle de la propret dun subjectile Partie 1: Degrs de rouil

3、le et degrs de prparation des subjectiles dacier non recouverts et des subjectiles dacier aprs dcapage sur toute la surface des revtements prcdents IMPORTANT The ref-erence photographs util-ized for the assessment of steel surfaces when using this part of ISO 8501 are not in-cluded in this electroni

4、c file because the quality of their reproduction is subject to change when they are viewed on screen or printed out. It is important that only the photographs contained in officially printed versions of this part of ISO 8501, purchased from ISO or from ISO member bodies or their distributors, are us

5、ed when carrying out as-sessments. IMPORTANT Les cli-chs photographiques reprsentatifs servant lvaluation visuelle des subjectiles en acier laide de la prsente par-tie de lISO 8501 ne sont pas inclus dans le pr-sent fichier lectronique parce que la qualit de leur reproduction ne peut tre garantie lo

6、rs-quils sont affichs lcran ou imprims. Il est important que seuls les clichs photogra-phiques contenus dans les versions officielles de la prsente partie de lISO 8501, achetes auprs de lISO, des comits membres de lISO ou de leurs distri-buteurs, soient utiliss lors des valuations. COPYRIGHT PROTECT

7、ED DOCUMENT DOCUMENT PROTG PAR COPYRIGHT ISO and SIS 2007/ISO et SIS 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writ

8、ing from either ISO or SIS at the respective address below. / Droits de reproduction rservs. Sauf prescription diffrente, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les mi

9、crofilms, sans laccord crit soit de lISO soit du SIS, lune ou lautre des adresses ci-aprs. ISO copyright office SIS, Swedish Standards Institute Case postale 56 CH-1211 Geneva 20 Sankt Paulsgatan 6 SE-118 80 Stockholm Sweden Tel. + 41 22 749 01 11 Tel. + 46 8 555 520 00 Fax + 41 22 749 09 47 Fax + 4

10、6 8 555 520 01 E-mail copyrightiso.org E-mail infosis.se Web www.iso.org Web www.sis.se Published in Switzerland/Publi en Suisse ISO 8501-1:2007 ISO 8501-1:2007(E/F) ii ISO and SIS 2007 All rights reserved ISO et SIS 2007 Tous droits rservs PDF disclaimer This PDF file may contain embedded typefaces

11、. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing

12、 Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized

13、 for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. PDF Exonration de responsabilit Le prsent fichier PDF peut conten

14、ir des polices de caractres intgres. Conformment aux conditions de licence dAdobe, ce fichier peut tre imprim ou visualis, mais ne doit pas tre modifi moins que lordinateur employ cet effet ne bnficie dune licence autorisant lutilisation de ces polices et que celles-ci y soient installes. Lors du tl

15、chargement de ce fichier, les parties concernes acceptent de fait la responsabilit de ne pas enfreindre les conditions de licence dAdobe. Le Secrtariat central de lISO dcline toute responsabilit en la matire. Adobe est une marque dpose dAdobe Systems Incorporated. Les dtails relatifs aux produits lo

16、giciels utiliss pour la cration du prsent fichier PDF sont disponibles dans la rubrique General Info du fichier; les paramtres de cration PDF ont t optimiss pour limpression. Toutes les mesures ont t prises pour garantir lexploitation de ce fichier par les comits membres de lISO. Dans le cas peu pro

17、bable o surviendrait un problme dutilisation, veuillez en informer le Secrtariat central ladresse donne ci-dessous. ISO 8501-1:2007(E/F) ISO and SIS 2007 All rights reserved ISO et SIS 2007 Tous droits rservs iii Page English text .1 Texte franais .23 Deutscher Text.45 Svensk text.69 Photographs / P

18、hotographies / Photographische Vergleichsmuster / Fotografier ISO 8501-1:2007(E) ISO and SIS 2007 All rights reserved 1 Contents Page Foreword .2 Introduction.4 1 Scope.7 2 Rust grades.8 3 Preparation grades.9 4 Procedure for visual assessment of steel substrates.12 5 Photographs .13 Annex A (inform

19、ative) Representative photographic examples of the change of appearance imparted to steel when blast-cleaned with different abrasives .15 Bibliography.19 ISO 8501-1:2007(E) 2 ISO and SIS 2007 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federat

20、ion of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committe

21、e. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance

22、with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires app

23、roval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 8501-1 was prepared by Technical Comm

24、ittee ISO/TC 35, Paints and varnishes, Subcommittee SC 12, Preparation of steel substrates before application of paints and related products. This second edition cancels and replaces the first edition (ISO 8501-1:1988). The main change is that the Informative Supplement ISO 8501-1:1988/Suppl.1994 ha

25、s been included as Annex A. ISO 8501-1:2007(E) ISO and SIS 2007 All rights reserved 3 ISO 8501 consists of the following parts, under the general title Preparation of steel substrates before application of paints and related products Visual assessment of surface cleanliness: Part 1: Rust grades and

26、preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings Part 2: Preparation grades of previously coated steel substrates after localized removal of previous coatings Part 3: Preparation grades of welds, edges and other areas with surface imp

27、erfections Part 4: Initial surface conditions, preparation grades and flash rust grades in connection with high-pressure water jetting ISO 8501-1:2007(E) 4 ISO and SIS 2007 All rights reserved Introduction The performance of protective coatings of paint and related products applied to steel is signi

28、ficantly affected by the state of the steel surface immediately prior to painting. The principal factors that are known to influence this performance are a) the presence of rust and mill scale; b) the presence of surface contaminants, including salts, dust, oils and greases; c) the surface profile.

29、International Standards ISO 8501, ISO 8502 and ISO 8503 have been prepared to provide methods of assessing these factors, while ISO 8504 provides guidance on the preparation methods that are available for cleaning steel substrates, indicating the capabilities of each in attaining specified levels of

30、 cleanliness. These International Standards do not contain recommendations for the protective coating systems to be applied to the steel surface. Neither do they contain recommendations for the surface quality requirements for specific situations even though surface quality can have a direct influen

31、ce on the choice of protective coating to be applied and on its performance. Such recommendations are given in other documents such as national standards and codes of practice. It will be necessary for the users of these International Standards to ensure that the qualities specified are compatible a

32、nd appropriate both for the environmental conditions to which the steel will be exposed and for the protective coating system to be used; within the capability of the cleaning procedure specified. ISO 8501-1:2007(E) ISO and SIS 2007 All rights reserved 5 The four International Standards referred to

33、above deal with the following aspects of preparation of steel substrates: ISO 8501 Visual assessment of surface cleanliness; ISO 8502 Tests for the assessment of surface cleanliness; ISO 8503 Surface roughness characteristics of blast-cleaned steel substrates; ISO 8504 Surface preparation methods. E

34、ach of these International Standards is in turn divided into separate parts. This part of ISO 8501 identifies four levels (designated as “rust grades”) of mill scale and rust that are commonly found on surfaces of uncoated erected steel and steel held in stock. It also identifies certain degrees of

35、visual cleanliness (designated as “preparation grades”) after surface preparation of uncoated steel surfaces and of steel surfaces after overall removal of any previous coating. These levels of visual cleanliness are related to the common methods of surface cleaning that are used prior to painting.

36、This part of ISO 8501 is intended to be a tool for visual assessment of rust grades and of preparation grades. It includes 28 representative photographic examples. Fourteen of these photographic examples show steel surfaces that have been subjected to dry blast-cleaning using quartz sand as the abra

37、sive. The use of other abrasives may affect the appearance of the surface. Colour changes caused by different abrasives are shown in Annex A. NOTE Twenty-four of the photographs originated from the Swedish standard SIS 05 59 00-1967, Pictorial surface preparation standards for painting steel surface

38、s. The other four photographs originated from the German standard DIN 55 928, Part 4, Supplement 1 (August 1978), Protection of steel structures from corrosion by organic and metallic coatings; preparation and testing of surfaces; photographic standards. INTERNATIONAL STANDARD ISO 8501-1:2007(E) ISO

39、 and SIS 2007 All rights reserved 7 Preparation of steel substrates before application of paints and related products Visual assessment of surface cleanliness Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings 1

40、Scope This part of ISO 8501 specifies a series of rust grades and preparation grades of steel surfaces (see Clauses 2 and 3, respectively). The various grades are defined by written descriptions together with photographs that are representative examples within the tolerance for each grade as describ

41、ed in words. It is applicable to hot-rolled steel surfaces prepared for painting by methods such as blast-cleaning, hand and power tool cleaning and flame cleaning, although these methods rarely lead to comparable results. Essentially, these methods are intended for hot-rolled steel, but blast-clean

42、ing methods, in particular, could also be used on cold-rolled steel of sufficient thickness to withstand any deformation caused by the impact of the abrasive or the effects of power tool cleaning. This part of ISO 8501 is applicable also to steel substrates that show residues of firmly adhering pain

43、t and other foreign matter (see Note 2 to 3.1) in addition to residual mill scale. ISO 8501-1:2007(E) 8 ISO and SIS 2007 All rights reserved NOTE 1 The preparation grades of previously painted steel surfaces after only localized removal of paint coatings form the subject of ISO 8501-2 1. This part o

44、f ISO 8501 relates the cleanliness of the surface to its visual appearance. In many instances, this is sufficient for the purpose but for coatings likely to be exposed to severe environments, such as water immersion and continuous condensation conditions, consideration should be given to testing for

45、 soluble salts and other invisible contaminants on the visually clean surface by the physical and chemical methods which form the subjects of the various parts of ISO 8502 2. The roughness characteristics of the surface should also be considered by reference to the various parts of ISO 8503 3. NOTE

46、2 This part of ISO 8501 contains the text in two of the three official languages of ISO, English and French. It also contains the text in German, published under the responsibility of DIN, and the text in Swedish, published under the responsibility of SIS. 2 Rust grades Four rust grades, designated

47、A, B, C and D respectively, are specified. The rust grades are defined by written descriptions. A Steel surface largely covered with adhering mill scale but little, if any, rust. B Steel surface which has begun to rust and from which the mill scale has begun to flake. C Steel surface on which the mi

48、ll scale has rusted away or from which it can be scraped, but with slight pitting visible under normal vision. D Steel surface on which the mill scale has rusted away and on which general pitting is visible under normal vision. Representative photographic examples of these rust grades are appended t

49、o this part of ISO 8501 (see Clause 5 for details). ISO 8501-1:2007(E) ISO and SIS 2007 All rights reserved 9 3 Preparation grades 3.1 General A number of preparation grades, indicating the method of surface preparation and the degree of cleaning, are specified. The preparation grades are defined in

50、 3.2, 3.3 and 3.4 by written descriptions of the surface appearance after the cleaning operation. Representative photographic examples of these preparation grades are appended to this part of ISO 8501 (see Clause 5 for details). Each preparation grade is designated by the appropriate letters “Sa”, “