交换机H3C(华三)基本命令 |
您所在的位置:网站首页 › h3c交换机配置大全 › 交换机H3C(华三)基本命令 |
学校一般会教思科交换机的命令,但出来工作基本会接触到H3C(华三华为跟3com合资公司,华为大家都懂的国货,国内的占有率不会少)的交换机居多。 H3C Switch命令 一、模式命令: 1. 用户模式:Switch> 2. 特权模式:Switch>enable Switch# 3. 全局配置模式:Switch#config terminal Switch(config)# 4. 接口配置模式:Switch(config)#interface fastethernet0/1 Switch(config-if)# 5. Line模式:Switch(config)#line console 0 Switch(config-line)# 二、特权模式下的命令: 1. 查看机MAC地址:Switch#show mac-address-table 2. 发现(CDP): Switch#show cdp Switch#show cdp interface fastethernet0/1 Switch#show cdp neighbors Switch#show cdp neighbors detail Switch#show cdp entry 3. 保存机配置: Switch#copy running-config startup-config或者Switch#write 4. 恢复交换机出厂值: Switch#erase startup-config Switch#reload 三、全局配置模式下的命令: 1. 配置主机名:Switch(config)#hostname Sw1 Sw1(config)# 2、 设置登陆台密码:Switch(config)#line console 0 Switch(config-line)#password 密码 Switch(config-line)#login 3. 使能口令:Switch(config)#enable Password 密码 4. 加密保存的使能口令:Switch(config)#enable secret 密码 5. 配置IP地址: Switch(config)#interface vlan 1 Switch(config-if)#ip address IP地址 网关 Switch(config-if)#no shutdown 6. 配置交换机网关:Switch(config)#ip default-gateway 网关 四、VLAN配置命令: 1. 创建vlan命令: a) 全局配置模式下: Switch)#vlan 2(config Switch(config)#name v2 Switch(config)#mtu 数值 Switch(config)#end b) Vlan数据库下: Switch#vlan database Switch#vlan 2 name v2 Switch#vlan 2 mut 数值 Switch#exit 2. 删除vlan命令: a) 全局配置模式下: Switch(config)#no vlan 2 Switch(config)#end b) Vlan数据库下: Switch#no vlan 2 name v2 Switch#exit 3. 在vlan中添加端口: Switch#config terminal Switch(config)#interface f0/1(端口) Switch(config-if)#Switchport mode access Switch(config-if)#switchport access vlan 2 Switch(config-if)#end 一次将多个端口添加到vlan中: Switch#config terminal Switch(config)#interface range f0/1 - 5(端口) Switch(config-if)#switchport access vlan 2 Switch(config-if)#end 注:switch#show vlan biref(查看vlan信息) 4. 配置vlan trunk: 1. 配置接口为trunk命令: Switch(config)# interface f0/1(端口) Switch(config-if)#Switchport mode trunk 2. 配置接口为动态协商模式的命令: Switch(config)# interface f0/1(端口) Switch(config-if)#switchport mode dynamic desirable/auto 3. 从trunk中删除vlan: Switch(config)# interface f0/1(端口) Switch(config-if)#Switchport trunk allowed vlan remove 2 4. 在trunk中添加vlan: Switch(config)# interface f0/1(端口) Switch(config-if)#Switchport trunk allowed vlan add 2 |
今日新闻 |
推荐新闻 |
CopyRight 2018-2019 办公设备维修网 版权所有 豫ICP备15022753号-3 |