桥接虚拟接口&;桥接域接口故障排除 |
您所在的位置:网站首页 › evc是什么意思 › 桥接虚拟接口&;桥接域接口故障排除 |
简介
本文档介绍如何了解桥接虚拟接口(BVI)和桥接域接口(BDI)并对其进行故障排除。 先决条件 要求对本文没有要求。 使用的组件本文档中的信息基于 ISR 路由器(对应于 BVI)和 ASR1K(对应于 BDI)。 本文档中的信息都是基于特定实验室环境中的设备编写的。本文档中使用的所有设备最初均采用原始(默认)配置。如果您的网络处于活动状态,请确保您了解所有命令的潜在影响。 背景信息BVI和BDI路由接口代表一组桥接的接口。例如,您希望桥接路由器上的两个接口,并且希望它们位于同一第2层广播域中。BVI/BDI接口将充当这两个桥接物理接口的路由接口。所有数据包流量都必须通过BVI/BDI接口。
2台PC到路由器的BVI连接 Cisco IOS®上的BVI路由器不会在同一广播域中配置两个或多个第3层接口(即同一子网中的两个或多个接口)。使用BVI接口将两台PC连接到路由器作为同一子网的一部分,并且仍然可以从这两台PC访问Internet。 您可以使用BVI执行此操作。 期限 定义 Bridge-group 将多个物理接口划分到一个逻辑组. 接口 BVI 可以路由的逻辑接口的第3层。 ISR 3 ISR 1 ISR 2 bridge irb bridge 1 protocol ieee bridge 1 route ip ! interface GigabitEthernet0/0/1 bridge-group 1 ! interface GigabitEthernet0/0/2 bridge-group 1 ! interface BVI 1 ip address 10.10.10.10 255.255.255.0 int fa0/0 ip address 10.10.10.1 255.255.255.0 int fa0/0 ip address 10.10.10.2 255.255.255.0 Cisco IOS XE上的BDIBDI与BVI类似,不同之处在于它运行在Cisco IOS XE上。 期限 定义 网桥域 表示第2层广播域。 网桥域接口 是允许第2层桥接网络和第3层路由网络之间双向流量传输的逻辑接口。 以太网虚拟电路(EVC) 是由提供商提供给客户的第2层服务的单个实例的端到端表示。在思科 EVC 框架中,网桥域由一个或多个称为服务实例的第 2 层接口组成。服务实例是给定路由器上给定端口上的 EVC 实例化。服务实例基于配置与网桥域关联。
两台交换机上的ASR连接 Cisco IOS XE平台上的BDI示例 A) 两台交换机上的 Fa0/1 都是第 3 层接口,并位于同一个广播域中。如果目的只是建立两台交换机之间的连接,则不需要在ASR上进行BDI配置。 ASR 1K SW1 SW2 interface GigabitEthernet1/2/3 no ip address negotiation auto cdp enable service instance 100 ethernet encapsulation untag bridge-domain 100 ! interface GigabitEthernet1/2/4 no ip address negotiation auto cdp enable service instance 100 ethernet encapsulation untag bridge-domain 100 interface FastEthernet0/1 no switchport ip address 10.1.1.1 255.255.255.0 interface FastEthernet0/1 no switchport ip address 10.1.1.3 255.255.255.0 后续步骤1.从SW1 ping SW2: BGL.Q.16-3500-1#ping 10.1.1.32.键入要中止的转义序列。 Sending 5, 100-byte ICMP Echos to 10.1.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/4/9 ms注:如果要在ASR外部路由,则需要配置BDI接口: interface BDI100 ip address 10.1.1.1 255.255.255.0 B)桥接两台交换机之间的多个VLAN。在物理接口下为每个 VLAN 配置单独的以太网虚拟电路 (EVC)。不支持在子接口下使用网桥域。 有两个VLAN:要桥接的VLAN 100和VLAN 200: ASR 1K SW1 SW2 interface GigabitEthernet1/2/3 no ip address negotiation auto cdp enable service instance 100 ethernet encapsulation dot1q 100 rewrite ingress tag pop 1 symmetric bridge-domain 100 ! service instance 200 ethernet encapsulation dot1q 200 rewrite ingress tag pop 1 symmetric bridge-domain 200 Exact same config under Gig1/2/4 interface GigabitEthernet1/2/4 no ip address negotiation auto cdp enable service instance 100 ethernet encapsulation dot1q 100 rewrite ingress tag pop 1 symmetric bridge-domain 100 ! service instance 200 ethernet encapsulation dot1q 200 rewrite ingress tag pop 1 symmetric bridge-domain 200 interface FastEthernet0/1 switchport trunk encapsulation dot1q switchport mode trunk interface Vlan100 ip address 10.1.1.1 255.255.255.0 interface Vlan200 ip address 10.1.1.2 255.255.255.0 interface FastEthernet0/1 switchport trunk encapsulation dot1q switchport mode trunk interface Vlan100 ip address 10.1.1.3 255.255.255.0 interface Vlan200 ip address 10.1.1.2 255.255.255.0 后续步骤1.从SW1 ping SW2上的int vlan100和vlan200: BGL.Q.16-3500-1#ping 10.1.1.32.键入要中止的转义序列: Sending 5, 100-byte ICMP Echos to 10.1.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/4/9 ms BGL.Q.16-3500-1#ping 10.1.1.33.键入要中止的转义序列: Sending 5, 100-byte ICMP Echos to 10.1.1.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/9 ms EPC monitor capture CAP interface gig1/2/3 efp 100 both match ipv4 any any packet tracer debug platform condition interface gig1/2/3 efp-id 100 ipv4 both EFP ID = 100 (service instance number) 相关信息 思科技术支持和下载 |
今日新闻 |
推荐新闻 |
CopyRight 2018-2019 办公设备维修网 版权所有 豫ICP备15022753号-3 |